Auteur Sujet: VU+ qui plante (Lu 7714 fois)

alexv · « **le:** 18 juin 2011 à 22:23:50 »

Bonjour à Tous,

J'ai un petit soucis avec une VU+Duo tout neuve, à mon habitude, j'ai flashé via USB avec un BH 1.6.2, pas de soucis, le flash a marché et la box m'a demandée de rebooter (ce que j'ai fait). Le premier reboot c'est bien passé et j'ai pu faire la config initiale.

Au reboot suivant la Vu est resté bloquée .... Au reboot suivant elle a démarrée.
La nuit suivante, alors qu'elle était en veille, elle s'est plantée, l'affichage indiquait 2h35 alors qu'il était 9h00 et la box ne répondait plus. La j'ai commencé à me poser des questions.

J'ai alors sortie mon câble série et refait un flash avec le nfi ,en me distant que c'était peut être un flsh plus poussé. mais cela n'a rien changé, la VU est aussi instable.

au boot lorsqu'elle plante elle s’arrête à

Code: [Sélectionner]

Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting internet superserver: inetd.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... done.
Starting automounter:

L'un de vous a t'il déjà rencontré ce problème ?

Merci D'avance
alex

Doume · « **Réponse #1 le:** 18 juin 2011 à 23:06:13 »

Peut-être commencer par flasher une autre image que la B.H ?

alexv · « **Réponse #2 le:** 19 juin 2011 à 22:45:18 »

Bonsoir,

En suivant tes conseils, j'ai essayé d'autres images (POD/VTI/Image officielle) c'est toujours la même chose, le flash marche tout le temps, mais ensuite, la box plante tout le temps. Je pense que c'est un problème physique. A mon avis, je suis bon pour un retour....

Je vous tiendrai au courant ...
merci
alex

sfinxx1 · « **Réponse #3 le:** 20 juin 2011 à 08:44:20 »

Bonjour,

A quel stade se bloque t elle ? (qu'est ce qui s'affiche à l'écran)
As tu mis un disque dur ? si oui essaye sans...

alexv · « **Réponse #4 le:** 20 juin 2011 à 21:58:51 »

Bonjour,

Elle ne se plante pas à un stade particulier, en suivant le boot via la console série, je vois que le plantage est aléatoire, par exemple, voici les traces de 3 reboot succéssif que je viens de faire à l'instant. L'image en flash est un BH dernière release, installée via USB.
(la box est vierge, pas de hdd, pas de clef USB)

Le Premier Boot ne donne rien à l'image

Code: [Sélectionner]


BCM73350010
012
Shmoo Version=1.9

MEMC-00000000 RW=00000010 WW=00000045 G=00000001 R=00000008 W=00000014
MEMC-00000001 RW=0000000D WW=00000047 G=00000001 R=00000007 W=00000001 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Wed Dec  9 17:23:18     2009 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd

DDR Freq:      395MHz
CPU speed:     405MHz
Memory Config: 32+16 non-UMA
Device Tech:   1Gb
Total memory:  384MB
Boot Device:   NAND
ECC:           Hamming
Total flash:   128MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.

checking usb
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3
Loading: 0x80001000/3734916 0x80390d84/144016 Entry address is 0x8036e000
TP1 Entry Address at 0x80000ffc = 8036e000
Starting program at 0x8036e000

<5>Linux version 2.6.18-7.3 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 SMP Thu Jun 2 19:00:03 CEST 2011
Fetching vars from bootloader... OK (E,D,B,C)
Detected 256 MB on MEMC0 (strap 0xe5430060)
CFE EnvVar: LINUX_FFS_STARTAD: 00000000, LINUX_FFS_SIZE: 07600000
CFE EnvVar: LINUX_PART_STARTAD: 07600000, LINUX_PART_SIZE: 00200000
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 09000000: RAM]
node [09000000, 07000000: RSVD]
<5>Reserving 112 MB upper memory starting at 09000000
<7>On node 0 totalpages: 65536
<7>  DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists.  Total pages: 65536
<5>Kernel command line: rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3 console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (37 instructions).
Synthesized TLB store handler fastpath (37 instructions).
Synthesized TLB modify handler fastpath (36 instructions).
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 203 Mhz
Using 202.501 MHz high precision timer.
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 141184k/262144k available (2981k kernel code, 120804k reserved, 523k data, 140k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
plat_prepare_cpus: ENABLING 2nd Thread...
TP0: prom_boot_secondary: Kick off 2nd CPU...
CPU revision is: 0002a044
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Brought up 2 CPUs
migration_cost=1000
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
brcm-pm: disabling power to USB block
brcm-pm: disabling power to ENET block
brcm-pm: disabling power to SATA block
audit: initializing netlink socket (disabled)
audit(946684800.257:1): initialized
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
loop: loaded (max 8 devices)
brcm-pm: enabling power to ENET block
Broadcom BCM7335 P20 Ethernet Network Device v2.0 Jun  2 2011 18:58:19
Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
blackhole initialised
Broadcom STB NAND controller (BrcmNand Controller)
i=0, CS[0] = 0
brcmnand_probe: CS0: dev_id=ecf10095
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB

Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d, tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
brcmnand_probe: CS0: dev_id=ecf10095
Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
        numchips=1, size=8000000
Creating 7 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000007600000 : "rootfs"
0x0000000007600000-0x0000000007800000 : "kernel"
0x0000000007800000-0x0000000007c00000 : "boot"
0x0000000007c00000-0x0000000007d00000 : "cfe"
0x0000000007d00000-0x0000000007d80000 : "mac"
0x0000000007d80000-0x0000000007e00000 : "env"
0x0000000007e00000-0x0000000007f00000 : "nvm"
usbmon: debugfs is not available
ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
brcm-pm: enabling power to USB block
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
 - USB h/w setup mode <B>
 - USB power enable set for active HIGH mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480608
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
jffs2_scan_inode_node(): CRC failed on node at 0x065f57f4: Read 0xffffffff, calculated 0x1490a44b
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 140k freed
INIT: version 2.86 booting
mount: mounting sysfs on /sys failed: Device or resource busy
Startting the hotplug events dispatcher
Synthesizing the initial hotplug events
Waiting for /dev to be fully populated
brcm-pm: enabling power to SATA block
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
scsi1 : sata_svw
ata2: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051011c
done
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
DVB: registering new adapter (bm750)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox remote control (native) as /class/input/input0
[LCD]: registered
[CI]:-BM750_PCB_2_1

[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113

[DFP]: bcm7335_max_i2c_write: Error 1114113

[DFP]: Scart 4707 is found 4

[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.

alexv · « **Réponse #5 le:** 20 juin 2011 à 21:59:29 »

Deuxieme boot , il va un peut plus loin (logo de boot sur la tv) mais se bloque

Code: [Sélectionner]


BCM73350010
012
Shmoo Version=1.9

MEMC-00000000 RW=00000010 WW=00000045 G=00000001 R=00000008 W=00000014
MEMC-00000001 RW=0000000E WW=00000047 G=00000001 R=00000008 W=00000001 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Wed Dec  9 17:23:18     2009 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd

DDR Freq:      395MHz
CPU speed:     405MHz
Memory Config: 32+16 non-UMA
Device Tech:   1Gb
Total memory:  384MB
Boot Device:   NAND
ECC:           Hamming
Total flash:   128MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.

checking usb
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3
Loading: 0x80001000/3734916 0x80390d84/144016 Entry address is 0x8036e000
TP1 Entry Address at 0x80000ffc = 8036e000
Starting program at 0x8036e000

<5>Linux version 2.6.18-7.3 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 SMP Thu Jun 2 19:00:03 CEST 2011
Fetching vars from bootloader... OK (E,D,B,C)
Detected 256 MB on MEMC0 (strap 0xe5430060)
CFE EnvVar: LINUX_FFS_STARTAD: 00000000, LINUX_FFS_SIZE: 07600000
CFE EnvVar: LINUX_PART_STARTAD: 07600000, LINUX_PART_SIZE: 00200000
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 09000000: RAM]
node [09000000, 07000000: RSVD]
<5>Reserving 112 MB upper memory starting at 09000000
<7>On node 0 totalpages: 65536
<7>  DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists.  Total pages: 65536
<5>Kernel command line: rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3 console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (37 instructions).
Synthesized TLB store handler fastpath (37 instructions).
Synthesized TLB modify handler fastpath (36 instructions).
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 203 Mhz
Using 202.501 MHz high precision timer.
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 141184k/262144k available (2981k kernel code, 120804k reserved, 523k data, 140k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
plat_prepare_cpus: ENABLING 2nd Thread...
TP0: prom_boot_secondary: Kick off 2nd CPU...
CPU revision is: 0002a044
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Brought up 2 CPUs
migration_cost=1000
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
brcm-pm: disabling power to USB block
brcm-pm: disabling power to ENET block
brcm-pm: disabling power to SATA block
audit: initializing netlink socket (disabled)
audit(946684800.257:1): initialized
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
loop: loaded (max 8 devices)
brcm-pm: enabling power to ENET block
Broadcom BCM7335 P20 Ethernet Network Device v2.0 Jun  2 2011 18:58:19
Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
blackhole initialised
Broadcom STB NAND controller (BrcmNand Controller)
i=0, CS[0] = 0
brcmnand_probe: CS0: dev_id=ecf10095
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB

Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d, tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
brcmnand_probe: CS0: dev_id=ecf10095
Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
        numchips=1, size=8000000
Creating 7 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000007600000 : "rootfs"
0x0000000007600000-0x0000000007800000 : "kernel"
0x0000000007800000-0x0000000007c00000 : "boot"
0x0000000007c00000-0x0000000007d00000 : "cfe"
0x0000000007d00000-0x0000000007d80000 : "mac"
0x0000000007d80000-0x0000000007e00000 : "env"
0x0000000007e00000-0x0000000007f00000 : "nvm"
usbmon: debugfs is not available
ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
brcm-pm: enabling power to USB block
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
 - USB h/w setup mode <B>
 - USB power enable set for active HIGH mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480608
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
jffs2_scan_inode_node(): CRC failed on node at 0x065f57f4: Read 0xffffffff, calculated 0x1490a44b
Empty flash at 0x065f5af0 ends at 0x065f6000
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 140k freed
INIT: version 2.86 booting
mount: mounting sysfs on /sys failed: Device or resource busy
Startting the hotplug events dispatcher
Synthesizing the initial hotplug events
Waiting for /dev to be fully populated
brcm-pm: enabling power to SATA block
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
scsi1 : sata_svw
ata2: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051011c
done
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
DVB: registering new adapter (bm750)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox remote control (native) as /class/input/input0
[LCD]: registered
[CI]:-BM750_PCB_2_1

[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113

[DFP]: bcm7335_max_i2c_write: Error 1114113

[DFP]: Scart 4707 is found 4

[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NTFS driver 2.1.27 [Flags: R/W MODULE].
mount: mounting /dev/sda1 on /media/hdd failed: No such file or directory
/dev/sda: No such file or directory
/dev/sda: No such file or directory
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1  2 0
[VID]: VIDEO_CONTINUE 1  1
[VID]: VIDEO_CLEAR_BUFFER 1  1 0
ldconfig: Can't open configuration file /etc/ld.so.conf: No such file or directory
[VID]: VIDEO_STOP 0  1
[VID]: VIDEO_SELECT_SOURCE 0
Starting virtual private network daemon: Autostart disabled.
crond[392]: crond (busybox 1.15.3) started, log level 8

Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... eth0      no wireless extensions.

udhcpc (v1.15.3) started
Sending discover...
Sending select for 192.168.0.208...
Lease of 192.168.0.208 obtained, lease time 7200
adding dns 212.27.40.240
done.
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting internet superserver: inetd.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... chown: unknown user ftp
Starting automounter:

alexv · « **Réponse #6 le:** 20 juin 2011 à 21:59:56 »

Le troisieme boot , il encore un peut plus loin (logo de boot sur la tv) mais se bloque toujours

Code: [Sélectionner]


BCM73350010
012
Shmoo Version=1.9

MEMC-00000000 RW=00000010 WW=00000045 G=00000001 R=00000008 W=00000014
MEMC-00000001 RW=0000000E WW=00000047 G=00000001 R=00000008 W=00000001 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Wed Dec  9 17:23:18     2009 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd

DDR Freq:      395MHz
CPU speed:     405MHz
Memory Config: 32+16 non-UMA
Device Tech:   1Gb
Total memory:  384MB
Boot Device:   NAND
ECC:           Hamming
Total flash:   128MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.

checking usb
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3
Loading: 0x80001000/3734916 0x80390d84/144016 Entry address is 0x8036e000
TP1 Entry Address at 0x80000ffc = 8036e000
Starting program at 0x8036e000

<5>Linux version 2.6.18-7.3 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 SMP Thu Jun 2 19:00:03 CEST 2011
Fetching vars from bootloader... OK (E,D,B,C)
Detected 256 MB on MEMC0 (strap 0xe5430060)
CFE EnvVar: LINUX_FFS_STARTAD: 00000000, LINUX_FFS_SIZE: 07600000
CFE EnvVar: LINUX_PART_STARTAD: 07600000, LINUX_PART_SIZE: 00200000
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 09000000: RAM]
node [09000000, 07000000: RSVD]
<5>Reserving 112 MB upper memory starting at 09000000
<7>On node 0 totalpages: 65536
<7>  DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists.  Total pages: 65536
<5>Kernel command line: rootfstype=jffs2 root=/dev/mtdblock0 rw mem=0x8000000 bcmrac=3 console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Synthesized TLB load handler fastpath (37 instructions).
Synthesized TLB store handler fastpath (37 instructions).
Synthesized TLB modify handler fastpath (36 instructions).
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 203 Mhz
Using 202.501 MHz high precision timer.
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 141184k/262144k available (2981k kernel code, 120804k reserved, 523k data, 140k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
plat_prepare_cpus: ENABLING 2nd Thread...
TP0: prom_boot_secondary: Kick off 2nd CPU...
CPU revision is: 0002a044
FPU revision is: 00130001
Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, linesize 64 bytes.
Synthesized TLB refill handler (23 instructions).
Brought up 2 CPUs
migration_cost=1000
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
brcm-pm: disabling power to USB block
brcm-pm: disabling power to ENET block
brcm-pm: disabling power to SATA block
audit: initializing netlink socket (disabled)
audit(946684800.257:1): initialized
JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
loop: loaded (max 8 devices)
brcm-pm: enabling power to ENET block
Broadcom BCM7335 P20 Ethernet Network Device v2.0 Jun  2 2011 18:58:19
Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
blackhole initialised
Broadcom STB NAND controller (BrcmNand Controller)
i=0, CS[0] = 0
brcmnand_probe: CS0: dev_id=ecf10095
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB

Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d, tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
brcmnand_probe: CS0: dev_id=ecf10095
Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
mtd->oobsize=64, mtd->eccOobSize=16
brcmnand_scan:  mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
        numchips=1, size=8000000
Creating 7 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000007600000 : "rootfs"
0x0000000007600000-0x0000000007800000 : "kernel"
0x0000000007800000-0x0000000007c00000 : "boot"
0x0000000007c00000-0x0000000007d00000 : "cfe"
0x0000000007d00000-0x0000000007d80000 : "mac"
0x0000000007d80000-0x0000000007e00000 : "env"
0x0000000007e00000-0x0000000007f00000 : "nvm"
usbmon: debugfs is not available
ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
brcm-pm: enabling power to USB block
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
 - USB h/w setup mode <B>
 - USB power enable set for active HIGH mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
 - Resetting at b0480608
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
jffs2_scan_inode_node(): CRC failed on node at 0x065f57f4: Read 0xffffffff, calculated 0x1490a44b
Empty flash at 0x065f5af0 ends at 0x065f6000
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 140k freed
INIT: version 2.86 booting
mount: mounting sysfs on /sys failed: Device or resource busy
Startting the hotplug events dispatcher
Synthesizing the initial hotplug events
Waiting for /dev to be fully populated
brcm-pm: enabling power to SATA block
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
scsi1 : sata_svw
ata2: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051011c
done
procmk_init
JFFS2 notice: (20) read_dnode: node CRC failed on dnode at 0x65f87c8: read 0xffffffff, calculated 0xdf149e99
dvb_bcm7335: module license 'Proprietary' taints kernel.
DVB: registering new adapter (bm750)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
DVB: registering adapter 0 frontend 0 (BCM7335 FE)...
[MPVR]: >> misc_pvr_init
input: dreambox remote control (native) as /class/input/input0
[LCD]: registered
[CI]:-BM750_PCB_2_1

[CI]: registered ci0
[CI]: registered ci1
[DFP]: registered dbox fp
[DFP]: bcm7335_i2c_write: Error 1114113

[DFP]: bcm7335_max_i2c_write: Error 1114113

[DFP]: Scart 4707 is found 4

[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NTFS driver 2.1.27 [Flags: R/W MODULE].
mount: mounting /dev/sda1 on /media/hdd failed: No such file or directory
/dev/sda: No such file or directory
/dev/sda: No such file or directory
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1  2 0
[VID]: VIDEO_CONTINUE 1  1
[VID]: VIDEO_CLEAR_BUFFER 1  1 0
ldconfig: Can't open configuration file /etc/ld.so.conf: No such file or directory
[VID]: VIDEO_STOP 0  1
[VID]: VIDEO_SELECT_SOURCE 0
bcm7335: hotplug_callback():
Hotplug - status.connected 0
bcm7335: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
bcm7335: hotplug_callback():
Hotplug - status.connected 0
bcm7335: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
Starting virtual private network daemon: Autostart disabled.
crond[390]: crond (busybox 1.15.3) started, log level 8

Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... eth0      no wireless extensions.

udhcpc (v1.15.3) started
Sending discover...
Sending select for 192.168.0.208...
Lease of 192.168.0.208 obtained, lease time 7200
adding dns 212.27.40.240
done.
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
bcm7335: hotplug_callback():
Hotplug - status.connected 0
bcm7335: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
bcm7335: hotplug_callback():
Hotplug - status.connected 0
bcm7335: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
bcm7335: hotplug_callback():
Hotplug - status.connected 0
bcm7335: hotplug_callback():
Hotplug - Disconnecting HDMI from display
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe

le fait que chacun des 3 boots progressent un peut plus n'est qu'un cas particulier, elle boot de temps en temps complétement (pas encore depuis le flash) , je peux faire l'installation, voir mes chaines, et puis au boot suivant elle replante ou même si je la laisse en veille, elle va se bloquer au bout de quelques minutes (quelques étant variable)
Je n'ai jamais vu ce comportement et mon fournisseur non plus alors qu'il en a écoulé des milliers. Si l'un d'entre vous a rencontré ce type de problème je suis preneurs de la solution retenue . Sinon, elle va faire un aller simple (et peut être retour) au SAV
merci
alex

re: je viens de comparer les sorties, les différences sont de types:

au début toute les lignes

Code: [Sélectionner]

MEMC-00000000 RW=00000010 WW=00000045 G=00000001 R=00000008 W=00000014
MEMC-00000001 RW=0000000E WW=00000047 G=00000001 R=00000008 W=00000001 #$

ont de légeres différences, mais je n'en connais pas la signification, c'est peut être normal

par contre dans la séquence de boot, je retrouve des différences de type

Code: [Sélectionner]

JFFS2 notice: (20) read_dnode: node CRC failed on dnode at 0x65f87c8: read 0xffffffff, calculated 0xdf149e99
ou 
Empty flash at 0x065f5af0 ends at 0x065f6000
JFFS2 notice: (20) check_node_data: wrong data CRC in data node at 0x065fb000: read 0xf6eace72, calculated 0x7a139653.

et là, ça ne me dit rien de bon ...

sfinxx1 · « **Réponse #7 le:** 22 juin 2011 à 08:06:10 »

Bonjour,

Effectivement on dirait une corruption de la partie flash en charge du boot, peut être défectueuse ?

Va falloir penser au SAV...

Doume forum

Auteur Sujet: VU+ qui plante (Lu 7714 fois)

alexv

VU+ qui plante

Doume

Re: VU+ qui plante

alexv

Re: VU+ qui plante

sfinxx1

Re: VU+ qui plante

alexv

Re: VU+ qui plante

alexv

Re: VU+ qui plante

alexv

Re: VU+ qui plante

sfinxx1

Re: VU+ qui plante